Jump to content

tzei

Solex
 View Profile  See their activity

  • Posts

    2,000

  • Joined

  • Last visited

  • Days Won

    15

  • Feedback

    0%

 Content Type 

Everything posted by tzei

  1. tzei
    Valve seals leak starts slowly. Sudden & that much oil - may have to dig deeper. Comp. test would tell something. Any noises?
  2. tzei
    Ok so I shoved tiny o-ring in stud cavity and smeared some Loctite SI 5910 to finish it off. Looks like it's holding. Thank You fellas.
  3. tzei
    Mitä aktuaalista vittua?! Perkele! First I thought that dist. bracket/leg/thingie gasket had given up. So I changed the gasket and the thingie just to be sure. No avail. Last two head bolts, in this case arp head studs, that are not under valve cover. The upper one lh side leaks oil from thread (after the nut) enough to require action. So how do I fix this?
  4. tzei

    Rocker panels

    tzei commented on tzei's blog entry in Z00Z

    Thx Well yes that was my first big concern. I think (hope) i got it right. So it should look like an 02 or at least as 02 as my white car - it's where I measured axle heights. Maybe I end up with Flintmobile
  5. tzei

    Rocker panels

    tzei commented on tzei's blog entry in Z00Z

    Lag is gone now. Track? At least a year more. Idk.
  6. tzei
    Yeah, that will get expensive… for many years.
  7. tzei
    1) slop in linkage 2) selector rod angled = not straight line from shift lever to gearbox selector shaft , R is first to bail.
  8. tzei
    You’ll need new used good cylinder in which you place plates & springs from the old one. Handle needs to come off so door card off. Take broken bits out from bottom of the door.
  9. tzei
    Top left #8 Steering column-trim panel/attach.p. | BMW 1502-2002tii 2002 M10 Europe BMWFANS.INFO Steering column-trim panel/attach.p. | BMW 1502-2002tii 2002 M10 Europe others don’t ring bell.
  10. tzei
    I think they started with manhattans, prolly still figuring out how to get out of that islet.
  11. tzei
    Uh i did those + boot lock.
  12. tzei
    I think i'm going for cigar now, later...
  13. tzei
    I just leave my spine in a wardrobe before doing those panels.
  14. tzei
    Rust makes them stick but i guess we’ll find out when disassemble them.
  15. tzei
    None of the bolts go thru water as is but to find moisture there (long bolt holes specially) is not uncommon. If liquids stays inside the engine and don’t find each other she’ll be alright.
  16. tzei
    Has to be legit.
  17. tzei
    I've used slightly modifyed normal allen bolts. Here is oe non-used.
  18. tzei
    That Muppet car vid shows a correct amount of steering play that i had in my Toyota Land Cruiser 😂
  19. tzei
    Ah 2x Dellorto 45 dhla w/ turbo kit. Those were the days 😂
  20. tzei
    No drinking and typing. 😛
  21. tzei
    Cattle Decapitation: The Prophets of loss
  22. tzei
    Can tc cover bolts be tightned or are tight enough?
  23. tzei
  24. tzei
    Well if one is able to lure it out without it noticing what’s going on then one might be able to convince it to play along. reuser
  25. tzei
    Just a plug against dirt, 6 mm nuts etc. #23111200477
×
×
  • Create New...