Jump to content

66Vette

Solex
  • Posts

    78
  • Joined

  • Last visited

  • Feedback

    0%

Everything posted by 66Vette

  1. I needed an excuse to get out of the garage and commiserate with other 02 owners with project cars. Ay carumba, bad timing for the rain
  2. Wow. The more I dig into these cars the stranger it gets. I'll pull the buzzer and tie the wires neatly away. Thanks guys
  3. Mike, really great explanation. While we have the column experts, the door buzzer on my car was unmounted and sitting in the bottom plastic cover. I am assuming since it has a mounting tab, it was supposed to be screwed down somewhere. Mine is electrically disconnected and I want to keep it that way, but I'd like to secure it in the proper manner. Thanks, Cris
  4. John: I think that answers it. I have the top piece (with VIN tag). I have the main plastic piece that holds the ignition switch, horn ring, etc. What I am missing is the bottom finish panel....doesn't surprise me! I am not sure I'll miss the bottom finish panel, but I'll start looking for one. So the bottom plastic piece is held to the column with the two B screws. The top piece is held on with the four A screws that go to into the bottom plastic piece. Thanks, Cris
  5. John, there is a "finish" panel that is separate from the bottom plastic panel? And it gets screwed to the plastic panel shown in my pic? (The C and D holes are different types and diameters.) Thanks, Cris
  6. Guys, thanks. I think bergie33 has the "D" hole mystery solved. visionaut, I did not notice the "C" holes were threaded, good catch. Did they mount something from the inside?
  7. Visionaut, thanks. The drawing only covers the "A" and "B" screws. Do you know what the "C" and "D" holes are for? Thanks, Cris
  8. I'm working on a 1975 2002 that was never quite put together properly. I am trying to figure out the steering column bottom cover screw holes. From the attached picture: The "A" holes take what looks to be a wood screw into the top cover (?), the "B" holes take a machine screw into a bracket on the steering column, but "C" and "D" are the mystery holes for me. Thanks, Cris
  9. In a former life, I designed some custom electronic instruments for a client of mine. I was always a fan of how older electronic instrument panels looked.. They were all done by engraving and then filling the letters/numbers/images with paint. You will also see this technique used on military equipment and aircraft. This method is very durable because you cannot rub off the engraving and paint (the paint is recessed in the engraving). I found an engraver near me who not only did engraving for trophies, etc but also did electronic instrument panels. He did my panels which included a logo and letters. The detail and appearance was exceptional. Much nicer than a silk screened panel or decals. Cost was in the neighborhood of $50 per panel. My panels were aluminum, though he did all the proofs in plastic.
  10. I am pretty much done with the driver's side footwell. This took twice as long as the passenger side. I have a little over two hours in it. The good news is there was almost no rust on the driver's side. The passenger side had a coating of surface rust. Maybe the "gooey" tar on the driver's side helped protect it. Ultimately, I'm glad I pulled the underlayment in the footwells. There was enough rust in the passenger side that if left unchecked might have caused some issues. It will get a good coating of Rustoleum, which should keep any issues at bay for decades here in California. Keep us posted on how well the dry ice trick works. There are mixed results on the web. Some swear by it, others have abandoned it. It may have to do with the type of underlayment. Hopefully it works on the 02.
  11. JQ02: I am using an all metal blade, it has a smooth chiseled edge. I did the passenger footwell in no time, but I just got out of the garage after stripping the driver side footwell. The driver side is not coming off as easy as the passenger side, lots of tar like goo. I've got an hour into it and it still needs some touch up. Let us know how the dry ice works.
  12. Has anyone used this product before? It seems well made, they have a testing set-up to allow comparison to other products like Dynamat, and it has a good following in the audio sound business. I've just never heard of them before and I am looking for sound deadening options. ResoNix Sound Deadener - CLD Squares - Full Box: 40 Pieces (40 Square Feet) - ResoNix Sound Solutions RESONIXSOUNDSOLUTIONS.COM ResoNix CLD Squares are the very best Constrained Layer Damper on the Sound Deadener market. Made with one factor in mind: Performance! Made In the USA!
  13. I have the unenviable task of removing the old tar paper underlayment from the front foot wells. I had read about dry ice, heat guns, and solvents and I was not really looking forward to any of these methods. I have used a multi tool or oscillating tool to remove caulk before and it moves through caulk like butter......so I tried my multi tool on the tar paper underlayment and it mows through it with ease and leaves a clean surface underneath. You use the blade with a smooth edge. Give it a try, it has worked great for me.
  14. I'm in the exact same situation. Is anyone using Resonix? Seems to have a solid reputation, and they have test results vs other manufacturers (albeit not independent tests). ResoNix Sound Deadening Materials RESONIXSOUNDSOLUTIONS.COM ResoNix Sound Solutions offers the best constrained layer damper sound deadeners on the auto, marine, industrial, and aerospace markets.
  15. I am in the same situation. I have a 2002 with an M20 swap that I am trying to make quiet and smooth for the street. My car has been cut up for flares etc, so I am thinking of cutting out the spare tire carrier (which I will never use) and getting some room for a real muffler. I am partial to Walker Quiet Flow mufflers. They come in a variety of configurations.
  16. I've never used this program so can't speak to the user interface, but this is used by many engine builders for header design. MaxRaceSoftware WWW.MAXRACESOFTWARE.COM I have used Engine Analyzer Plus. If I remember correctly it allows some of the header parameters to be specified and you can see the impact on HP and Torque. This program was pretty accurate predicting HP on a small block chevy build. I feel its best use is to evaluate differences when making changes like cam specifications, not so much on nailing down an exact HP figure. For an M10, you may have to be creative in entering things like intake manifolds. And remember, GIGO. https://www.performancetrends.com/
  17. VW: I kinda like the look of those mats. Did they fit well? You happy with them? Looks like they make ones specifically for the 02.
  18. I know it sounds red neck, but the old tire method works well. I would recommend you remove the alternator and any other bits that hang out and are not reasonably stout. I use a relatively wide tire, lay foam pads on the bottom and insides of the tire, and slowly drop the engine into the tire. The tire kinda forms to fit the engine shape. I use ratchet straps to tie the engine down securely from there. I've moved a handful of engines this way from small block chevies, a chevy inline six, and a BMW M20.
  19. Mike, I have to remove the sound deadening/vibration dampening pads on my 75. I was going to try my multi-tool as well. By flexible blade do you mean the one with a smooth cutting edge? I have used mine to remove caulk and it does a truly amazing job, peeling it up like it was buttah. Did you try adding heat at all? Thanks, Cris
  20. Piston to wall clearance is measured as the bore diameter - piston diameter. How To Check Piston To Wall Clearance BLOG.DIAMONDRACING.NET Checking piston-to-wall clearance is a critical measurement every engine build should include. Here is a detailed walk through of how to measure your piston-to-wall-clearance.
  21. Seems pretty odd to me things are so far off. I looked at your piston spec sheet and the alloy was not specified. I would guess if they are calling out .006" clearance, the pistons are made from 2618 aluminum alloy as opposed to 4032 alloy. 2618 is typically used in applications where the pistons will see more abuse. 2618 is more ductile but has more thermal expansion so piston clearances go up. At least that is the old school pitch on piston material. If you have a build sheet from the machine shop, it seems like (maybe) they were somewhat reputable. Hard to believe they were that far off in dimensions, and I doubt you would see that kind of wear. Is it possible someone was trying to make this a turbo build and added even more clearance for boost. Either way, rebore and new pistons would be the way I would go. You've got the whole thing torn down, a shame not to make it right. Modern pistons and rings are also better.
  22. Wow!! I was about to write in about these strange pins I found sticking out of my floor after I stripped the interior. Looks like they were there from the beginning.
  23. Thought I would follow up on this topic. I was able to find the socket part number, or something very close. It did not take Columbo to sleuth this out. I pulled one of the sockets out of the cluster connector and it was stamped "AMP". I did a little digging and I found the Amp (Amphenol or now TE Connectivity) socket. It is a standard, widely used part, and you can find it anywhere. The part number is 60617-X, the X is for the plating and material. I used one with gold plating and made of phosphor bronze. The tin plated sockets are the cheapest. Attached is a picture of an old wire with its socket (green wire), and a new socket (brown wire). Also attached is the tool I used to remove the sockets from the cluster connector. The sockets have only one barb to hold them in place so a thin, flat piece of metal to depress the barb would work as well.
  24. I didn't do a thorough examination, but the Fuyao glass defroster looked more nicely made than the Duro-Glas. Can't comment on the glass itself.
×
×
  • Create New...