Jump to content

mikea

Solex
 View Profile  See their activity

  • Posts

    118

  • Joined

  • Last visited

  • Feedback

    0%

 Content Type 

Everything posted by mikea

  1. mikea
    thanks for all the input super helpful mike
  2. mikea
    I just bought a set of NOS Euro front turn signals the bulb terminal seems to only have 1 wire whereas the old one of course have two for turn signal/4 way flasher & for running lights do the Euro turn signals not have running lights? any info appreciated mike
  3. mikea
    any one have any photos that show how you routed the extra long hydraulic line for the clutch slave cyl. I have the two-piece assy I got from Ireland short piece of flex hose and short length of steel line. any pics of a neat install would be super helpful thanks Mike '74 2002
  4. mikea
    when i took my instrument cluster out I could see the fog light switch just looks like a dummy knob with no switch behind it. I want to eventually put on fog light in front. is this the same switch part number as the headlight switch? anyone have the correct part number, or a good place to buy? mike-Berkeley '74 2002
  5. mikea
    thanks what about reduced ZDDP additives in modern formulations? is this an issue for older engine designs?
  6. mikea
    maybe this has been flogged to death on here already I am dropping in newly rebuilt engine in my '74 2002 carb. anyone want to weigh in on which oil I should use? synthetic? ZDDP issues? oil change intervals? thanks Mike Berkeley CA
  7. mikea
    sorry I missed- had to go away from my computer today till now mike
  8. mikea
    OK I'd like to buy these how do you want to handle the details I'm in Berkeley CA Mike
  9. mikea
    will these fit my '74 ? mike
  10. mikea
    thanks guys! got it out no problems yes did undo speedo first mike
  11. mikea
    how does it come out? on my mercedes W123 it some out with 2 pieces of bent wire but on the 2002 it is very tight! I don't want to break anything. any tricks? mike berkeley ca 1974 2002
  12. mikea
    I am about to drop in a newly rebuilt engine. the trans. is bolted up. what's the best way to find TDC or install the dist. so that I can start it and run it to use a timing light? it's a vacuum advance dist. mike berkeley CA 1974 2002
  13. mikea
    do you offer that part? are all three the same? mike
  14. mikea
    any one know the part number for the plastic clips/clamps that secure the steel brake lines that cross over to the passenger front, against the firewall? Plus one more clip/clamp on the brake booster bracket? I can't find these in the diagrams at maximilian etc Mike-berkeley 1974 2002
  15. mikea
    putting my car back together. I am bending new brake lines- and I kind of lost track of old set up. any one have pics showing the routing inside the engine compartment? have new NC, new lines, new everything. engine is out of car. any photos appreciated ! mike 1974 2002
  16. mikea
    back to my project after long hiatus I installed a rebuilt steering box, new links etc. question, should the pitman arms hit against both stops on the subframe? as you can see from this photo. when the steering box runs out of travel, the arm is not against the stop. if i move the arm on the splined shaft, then the gap is on the idler side. i cant get it to hit the stop on both sides any ideas? is this a problem? mike 2002 1974
  17. mikea
    you're right- i should have looked there. torqued it up more, and now the washer turns together seems correct thanks mike
  18. mikea
    just putting my steering together. any help appreciated. 1. castle nut on top of idler bolt- what is torque value to tighten this? 2. I have tightened it so far what seems right- QUESTION: should the silver washer turn with the idler bolt? it now does not. when I move the idler link, the castle nut turns on top of the steel washer. Is that the way that this should function? or should the silver washer be turning with the nut? thanks mike 2002 1974
  19. mikea
    I have come to terms with all the rust work my "california car" needs ( the old British Columbia phone book I found under the back seat was an indication of how expensive my education would be) I found these weird scars in the inner wall- right where the door brake is. is this an accepted/required way to service the door brakes? it's on both sides. any ideas? should I have the body shop weld these back up? I ripped out all carpet tonight. when I took out the seat belts I saw the indicator wires. What's the best way to terminate those wires? back to the fuse panel? thanks all for your help so far. As soon as I get the rebuilt steering back together this thing gets rolled to the body shop, rust repair, and then back to my house to receive the rebuilt motor. Mike 1974 2002
  20. mikea
    Trunk Floor 41121838992 hey I am about to buy one of these. I can't tell from your various posts if this is available or not if it is let me know Mike Berkeley CA
  21. mikea
    there are some kind of fiber or rubber washers on those tapered shafts you can check if they are still intact
  22. mikea
    I have a brand new center link on my bench- installing this weekend. Correct: the tapered ends of the center link do not themselves swivel. That's not to say it can't stand replacing- I figure this stuff is 35+ years old....
  23. mikea
    hey I see you're in Alameda I don't how far you're taking this but I just redid my steering assembly I had the subframe, struts and assorted goodies powder-coated at Leon's Powder Coating in Oakland Very reasonable, and I got it back the same day Mike Berkeley
  24. mikea
    Jerry I am going to place an order with Walloth u. Nesch this week. they have floor pans ( actually on sale this month) I think the landed cost per pan will be lower with a larger order. If you ( or anyone in the bay area) are still interested let me know I will be pulling the trigger latest Tuesday Mike
  25. mikea
    sure, let's collaborate on this. what city are you located? let me know what you find out mike
×
×
  • Create New...