Jump to content

Scottjeffrey

Solex
 View Profile  See their activity

  • Posts

    870

  • Joined

  • Last visited

  • Feedback

    100%

 Content Type 

Everything posted by Scottjeffrey

  1. Scottjeffrey
    Same here Rob. Big and honking, lol. Thanks so much.
  2. Scottjeffrey
    Rob, may I ask what size holes you'd punch out (bought a set of Pittsburg punches at Harbor Freight yesterday) if you weren't using the bulkhead system, only passing hoses through, for the six and ten hose that will take a grommet and allow for the hose to pass through? Many Thanks- Scott
  3. Scottjeffrey
    Hi Rob and thanks. I have the template. Just was looking for a visual pic from the engine side. Trying to get my bearings to not make a mistake. I didn't even think to look in your book which helped me tremendously to revamp my Fridgiking system. I put a pin through the factory installed plug behind the brake lines for orientation. I want to get it right! Thanks as always!
  4. Scottjeffrey
    Hi All, I am changing my fridgiking evaporator and fascia/surround to a Behr unit. I am trying to pin down where to punch out the holes in the firewall and want to get it right. Would anyone have a picture of the two hoses passing through the firewall from the engine side? Thanks very much for your time, effort and help. Scott in Fort Lauderdale
  5. Scottjeffrey
    Thank you, Mike!
  6. Scottjeffrey
    One million thank you's, John.
  7. Scottjeffrey
    HI John, Thank you so much. This makes sense. By mounting bar you mean the part in the picture (three bolts and one nut to motor)? Best wishes - Scott
  8. Scottjeffrey
    Looks like a second washer in the second picture and not in first. Hmmm...But neither post extended farther than the other to allow the nut to engage.
  9. Scottjeffrey
    I am currently perplexed by not being able to get my windshield wiper posts to extend far enough out to get the nut on over the exterior washer. I had it out and replaced it and it was fine before the car went to the paint shop 18 months ago. It's finally home. So I put my rubber ‘grommets’ and the rings in and could not get it to work. What may I be ‘missing’ here? Enclosed are pics taken from under the cowl. I hope I don’t have to pull it all out the side again. Many Thanks, Scott
  10. Scottjeffrey
    Many thanks! I did procure one. Best Regards, Scott
  11. Scottjeffrey
    Hi All, I am getting ready to install fresh belt line molding after a repaint. Waiting on its arrival and readying fasteners. I have a few questions 1) T clip on left hole, plastic on right? 2) T clip on left hole, plastic on right? 3) Left to right. T clip, plastic, plastic? Many Thanks, Scott
  12. Scottjeffrey
    Yes.
  13. Scottjeffrey
    Looking for one of these. Goes over wiper arm posts before washers and nut. Thank you, Scott
  14. Scottjeffrey
    I am going a little crazy here as I begin to install the quarter glass rubber. OEM. They were removed by the body shop (they had been installed but removed for third (!) respray. I am having a very hard time believing they were correctly marked; right and left. Seems switched to me. I went a took a URO seal out of its bag (I had bought them but decided to go OEM). It's part number marked on the bag was for the driver's side. It seems like it should be for the passenger to my newbie eye. In the photo below from the piece marked left, the highlighted part seems to me to go under the aluminum horizontal piece but only can if I put it on the passenger side. Trying it on the driver's side looks to me all wrong. I am feeling a bit foolish. Your help is much appreciated. Best Regards, Scott
  15. Scottjeffrey
    Looking to buy passanger side, rear quarter window latch. Went to body shop where car was painted, to install rubber and glass myself. They had broken it Many Thanks, Scott in Florida
  16. Scottjeffrey
  17. Scottjeffrey
    All buttoned up. Learning curves make me smile.
  18. Scottjeffrey
    Looking to buy one of these for my A/C evaporator housing. Many Thanks, Scott. SJWIN56@aol.com
  19. Scottjeffrey
    No luck from the manual, although I believe I figured out where the flat spots go. Putting the two halves together after correct placement (I think), hasn't 'worked so far'. I feel optimistic though. I've learned it can often take a million tries until, 'Bingo', lol. Thanks for your help!
  20. Scottjeffrey
    I am changing the A/C components inside the car from a Fridgiking to Behr unit. I opened up the Behr housing after receiving it in the mail to check things out in there. I tried a trial reassembly and had trouble due to the plastic pieces which fit in grooves on both sides of the housing. They each have a flat spot and I don't know where it is supposed to located. Every which way I try leads to the cages rubbing against them Any help would be much appreciated. Many Thanks, Scott in Fort Lauderdale
  21. Scottjeffrey
    Thank you very much. I am still looking!
  22. Scottjeffrey
    Thank you, Steve. I remember that Michelin on my 2002's decades ago. What size are yours? Scott
  23. Scottjeffrey
    Hi Steve, What tires are on your 2002? THanks, Scott
  24. Scottjeffrey
    Thank you, Mike. A very Merry Christmas to you! Scott
  25. Scottjeffrey
    Thank you. I can't find any of the Vredestein Sprint Classic in 13 inch unfortunately. I really liked what you said. Scott
×
×
  • Create New...