Jump to content

02MonsterMike

Solex
  • Posts

    40
  • Joined

  • Last visited

  • Feedback

    0%

Everything posted by 02MonsterMike

  1. $50 shipped from Detroit, MI. Thanks, Mike
  2. positive side of the coil. I've run a battery relocation cable from the E30, and have the distribution block. Does the wire go directly to there? I've looked at the wire schematic and it shows a wire coming from the ignition switch....I can't find that.... I was able to turn over the engine...but obviously not started yet... Please help. Thanks, 02Monster
  3. the front subframe at the engine mount bolt? I did a battery relocation to the trunk. Is there anywhere else that other people have used as a ground? Thanks 02Monster
  4. Needed in excellent condition...no dings, scratches, or oxidation. Email me at 2002monstermike at sbcglobal dot net
  5. Has the terminal, and bolts. About 3 inches is cut from the battery end....but you will need to splice in about two feet of 1 aught cable either way to relocate to between the shock towers in the trunk. $50 shipped. Thanks, 02Monster
  6. do you need both inboard and outboard for passenger and driver seats, or just driver seat? Thanks, 02Monster
  7. I've got a Weber 38/38 and I need to add a fuel return line to the carb. It currently has one fuel inlet and one plug. I need to remove the plug and replace with another fuel inlet. anybody have one available? Thanks 02Monster
  8. Email me at 2002monstermike at sbcglobal dot net
  9. $150 shipped. Rewrapped with the low gloss tartan tape. Let me know. 2002monstermike at sbcglobal dot net.
  10. Done... - front 22mm sway bar with urethane bushings and new links -new rotors and pads Doing this weekend... -new Bilstein sport strut inserts -new upper strut bearings -new urethane bushings Haven't looked at ball joints or tie rod ends. New engine mounts and steering coupler to follow... Thanks 02MonsterMike
  11. I'm replacing the front bushing on my friend's car.....its shakes, rattles and makes lots of noise when he drives it. I went through the search function here and was unable to find a procedure or trick to getting the old rubber bushings out of the lower control arms. Wasn't there a long bolt with large and small washers setup that somebody used to get the bushings out? Any help would be great....I have this weekend to do it since he's out of the country on business. Also, does somebody have a procedure to tune a Weber 32-36 so that its not so rough at idle? Thanks Mike
  12. have we met? 02MonsterMike 2002MonsterGarage Waterford, MI
  13. I just measured the various driveshafts that I have and some are (measured from flange to flange, without guibo or bolts) as being either 600mm or approximately 548mm. Is the longer one for the 4-speed? Trying to sort things out. Thanks 02MonsterMike Job news to come....I just need to get my head around some things first.
  14. I've been infatuated with the Subaru WRX STi exhaust sound lately, and I need to find out how I can attain that same sound with a BMW 2002. I'm going to be running an engine with 12.5:1 CR, Schrick 292, Weber 38/38, and a tii exhaust manifold. Any suggestions. TIA 02MonsterMike
  15. NSU 1200 TT in vancouver, BC http://cgi.ebay.com/ebaymotors/NSU-TT-1200-the-1200-is-the-sporty-NSU-twin-carbs-etc_W0QQitemZ4625805879QQcategoryZ6472QQrdZ1QQcmdZViewItem
  16. I emailed the guy and didn't reply....The photos that are in this auction are the same photos for the last auction. I'd be very careful. 02MonsterMike
  17. check them all and let me know? Thanks...I really appreciate it. 02MonsterMike PS....can anyone recommend a free photo hosting site....I won't have my Earthlink FTP site for much longer. Thanks again. http://motors.search.ebay.com/_W0QQsassZ02monster
×
×
  • Create New...