Jim Blaschke

Solex
  • Content Count

    29
  • Joined

  • Last visited

  • Feedback

    N/A

Community Reputation

7 Neutral

About Jim Blaschke

Contact Methods

  • Website URL procareautomv.com

Profile Information

  • Gender Male
  • Location Mission Viejo, CA

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Jim Blaschke

    Rear panel

    What is the best source for this rear panel for my 1971 Thanks in advance. Sent from my iPhone using Tapatalk
  2. Jim Blaschke

    1971 front grills wanted

    Looking for nice driver quality grills for my 1971 2002. Sent from my iPhone using Tapatalk
  3. Jim Blaschke

    Reproduction front grill?

    That’s what I am talking about. It seems very do able to reproduce these units in a high quality plastic type material. Computer scan an OE unit, draw it up on a system and make the necessary adjustments and send to printing. We don’t need these units to be made in the same type of aluminum type metal. What we need is a reasonable priced option that will get the job done so we can spend our hard earned money on other areas of our cars other than these 3 expensive pieces. Call me me crazy for thinking so “out of the box”.
  4. Jim Blaschke

    Reproduction front grill?

    I have the center kidney but need the right and left side grills. Don’t need show quality. Decent driver quality part ok by me. Thanks
  5. I know this has probably already been asked, are there any suppliers of a reproduction front griils for 1968-1973 cars? Something in plastic? Anything? It seem to me that just about anything today can be copied to a high standard with modern re-engineering and technology. I purchased my project car with missing grills and am having a difficult time sourcing even used units. Thanks in advance for the insight.
  6. Jim Blaschke

    Stock seats and door cards

    Interested in front seats. How much and where is your location. Thanks Sent from my iPhone using Tapatalk
  7. Jim Blaschke

    FS almost new Weber 32/36 carb

    I would like to purchase. Pm me please. Thanks Jim Blaschke Sent from my iPhone using Tapatalk
  8. Jim Blaschke

    Lack of proper vacuum advance

    Another pic of the two back sides of the intake manifold. Sent from my iPhone using Tapatalk
  9. Jim Blaschke

    Lack of proper vacuum advance

    Ok, I get what everyone is saying. I bought my car with a trunk full of extra parts. I have two 2 barrel intakes, one Solex carb and 1/2 of Solex carb. My crazy thinking is, they were in the trunk for a reason? My question is, which of the two manifolds should I use and is the pictured Solex carb a good proper candidate to attempt to rebuild? The group thoughts please. Thanks Sent from my iPhone using Tapatalk
  10. Jim Blaschke

    Hundreds of 2002 and 2002 Tii Rare Parts

    Lever near the floor. Thanks
  11. Jim Blaschke

    Hundreds of 2002 and 2002 Tii Rare Parts

    Looking for the 2 horns and the horn relay. Also passenger side seat adjuster lever. Both drivers and passengers side knee moldings. Thanks
  12. Jim Blaschke

    Lack of proper vacuum advance

    Thanks for all the comments telling me to replace my sub par carb. Upgrade is in order but until then I would like to spend my funds on other areas of the car. Anyone have a recommendation to fix other than an obvious replacement. Thanks
  13. Jim Blaschke

    Lack of proper vacuum advance

    The electric solenoid looks as if it had been disabled by PO. I thought this was mainly used as an electronic chocking device for cold starts? The current set up has a manual choke mechanism. If this isn’t the choke, what is it, and should it be hooked up? Thanks
  14. I acquired a 1971 with a 1 barrel Weber 34 carb. My problem is the only vacuum line coming off the carb going to the distributor always has full vacuum. I believe I should have an additional/different port the adjusts/pulls more vacuum as the rpms increase. My has full vacuum all the time. I included a few pics. I also noted 2 spots on the carb that I believe my be a source of the vacuum I am looking for if tapped out? Not sure? Sent from my iPhone using Tapatalk
  15. Jim Blaschke

    Hundreds of 2002 and 2002 Tii Rare Parts

    Looking for the drivers side and passenger side knee trim for both door. I have a 1971 model year. Thanks Jim Sent from my iPhone using Tapatalk