Jump to content

jcnnjc

Solex
  • Content Count

    73
  • Joined

  • Last visited

  • Feedback

    0%

Everything posted by jcnnjc

  1. looking for a stock downdraft manifold for my 1974 02 doing some work on my sidedrafts want one to use during the down time let me know price with shipping to zip 30265 Thanks Jim
  2. jcnnjc

    parts lot

    how much for the stock intake and is that a solex carb on it? Thanks Jim
  3. Yes a have a header, and carbs were rebuilt before I installed them
  4. I just installed a set of 40 DHLA's on my 74 o2 with a 292 cam here are the spec's of the carb's 30 Venturis 7848.3 aux Venturi 60 idle jets 140 main jets 7772.11 emulsion tubes 42 pump jets 200 air correct tubes I put in a wideband gauge around 11 at idle 12-13 at cruise around 14 at wot i am getting some popping at idle and I not happy with power at upper rpms, I have searched quite a bit and from every thing I see my choke s at a little small at 30 but some recommend 32 some 34 and some 36 also not sure about the idle jet and main jet, they should be close but? any help would be welcome! Thanks, Jim
  5. http://parts.bmwofsouthatlanta.com/showAssembly.aspx?ukey_assembly=249648&ukey_make=980&ukey_model=13499&modelYear=1974&ukey_category=17306&ukey_driveLine=6494&ukey_trimLevel=11924 I havent either but it says qty per car 8, so it must be per half? check the link if it works
  6. Does anyone know where they sell this size, I can only find 1 place and thats BMW they want 13 bucks each My motor is a factory replacement motor and it had 1st over on mains and 3rd over on conn rods will have to find a new crank if I cant find bearings? Thanks Jim
  7. what size ball hone or dingleberry hone size do I need looks like they have them in 89mm and 95mm the motor has not been bored out so so it should be close to 88.97 stock dont know if the 89 will do it or if the 95 is 2 big? Thanks Jim
  8. any one need these seats? or if anyone needs parts off of them let me know Thanks Jim
  9. Shipping is $25.00 What is best way to order? Let me know Thanks, Jim
  10. I have the front seats from my 74 they look to have been recovered at some time. still comfortable to sit in, but horse hair is coming out a little, drivers bottom seams are starting to separate, pass seat is pretty good. black hinges are ok, small amount of rust on headrest rails, Bumpers are good for a driver no big dents dings will sent photos if there is interest part are located in Newnan Ga 25 miles sw of Atlanta would like to trade for 02 parts, needs are belt trim bits, starter, dome light for non sunroof or whatever you might have? also need good 4 speed tranny, would add cash for that. pick up only.
  11. if either deal falls through I will take one Thanks Jim
  12. Are these still for sale? if so shipping quote to 30265 Thanks Jim
  13. Bryce, Forgot to ask if the lower clamshell has the hole for a manual choke? Let me know Thanks Jim
  14. Do you still have the motor and tranny? Let me know Jim
  15. Hello Bryce, did you see my message? Let me know Jim
  16. Will you do $70 shipped? if so I will take the lot also let me know paypal info and I will send funds asap thanks Jim
  17. interested in steering whell clamshell and under dash panels with shipping to zip 30265 Thanks Jim
  18. How are the under dash panels? also I need the plastic panel that goes under the steering wheel support let me know with shipping to zip 30265 thanks Jim
  19. very interested in tranny and maybe motor depending on price, email me at jcnnjc@yahoo.com Thanks Jim
  20. do you still have the motor and tranny? might also need drive shaft, if so let me know. Thanks Jim
  21. Here is the one I have on my 74 http://dtmfiberwerkz.com/access/2002-turbo-style-front-bumper-p-433.html Its not as nice as the one I got from I.E. many years ago but it should work for you Jim


×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.