Jump to content
  • When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Replacing Struts While On The Car


Beach_Bum

Recommended Posts

This is actually a project that I'm just about to embark on also so while we're on the topic I'd like to verify what seems to be the consensus as to the proper method.  Please correct any steps that aren't right:

1.) Jack up, jack stands, etc.

2.) Remove wheel and brake caliper (hang out of the way, no need to disconnect hydraulics)

3.) Cut the safety wire and undo the three bolts holding the strut to the control arm

4.) Separate tie rod end from front knuckle.

5.) Undo three top mount bolts on top of fender well

6.) Remove if enough clearance, if not, go to steps 7 and 8.

7.) Disconnect stabilizer bar link from control arm

8.) Disconnect control arm and radius link from front subframe.

 

That all sound right?  Also, does anyone know where to get new spring pads/seats?  I figure I ought to replace those while I have everything apart.  Thanks!

 

-Carl

 

Here are some links with pictures that I've been studying. Maybe they'll help you as well:

 

http://www.cyclopticgaze.com/2002/26front_rebuild.html

 

http://www.bmw2002faq.com/topic/124160-two-essential-tools-for-ball-joint-replacement/

 

About 3/4 of the way down on this link:

http://www.bmw2002faq.com/topic/116731-m20-triple-weber-build-x2/page-2

 

 

Here is the wire I used:  http://www.skygeek.com/ms20995c32.html

 

I wouldn't hurt to replace the "special" bolts after you get them out.  I got mine from Blunt.  Soak those bastards good with some penetrant.  You don't want to have to drill'em out!

 

Thanks!

Edited by Beach_Bum
Link to comment
Share on other sites

This is actually a project that I'm just about to embark on also so while we're on the topic I'd like to verify what seems to be the consensus as to the proper method.  Please correct any steps that aren't right:

1.) Jack up, jack stands, etc.

2.) Remove wheel and brake caliper (hang out of the way, no need to disconnect hydraulics)

3.) Cut the safety wire and undo the three bolts holding the strut to the control arm

4.) Separate tie rod end from front knuckle.

5.) Undo three top mount bolts on top of fender well

6.) Remove if enough clearance, if not, go to steps 7 and 8.

7.) Disconnect stabilizer bar link from control arm

8.) Disconnect control arm and radius link from front subframe.

 

That all sound right?  Also, does anyone know where to get new spring pads/seats?  I figure I ought to replace those while I have everything apart.  Thanks!

 

-Carl

delete items 4,7 and 8.

 

two caliper bolts, three lower strut bolts, three upper strut nuts and take it out.

 

edit....and the one little bolt that holds the brake hose bracket to the strut....i forgot about that one as i don't use it on my car.

Edited by mlytle

2xM3

Link to comment
Share on other sites

Blue loctite works on it too. I havent had an issue 20k in with mine... Proper torque is very important!

-Nathan
'76 2002 in Malaga (110k Original, 2nd Owner, sat for 20 years and now a toy)
'86 Chevy K20 (6.2 Turbo Diesel build) & '46 Chevy 2 Ton Dump Truck
'74 Suzuki TS185, '68 BSA A65 Lightning (garage find), '74 BMW R90S US Spec #2

Link to comment
Share on other sites

What is the proper torque on those?

 

     DISCLAIMER 

I now disagree with some of the timing advice I have given in the past.  I misinterpreted the distributor curves in the Blue Book. 

I've switched from using ported-vacuum to manifold, with better results. 

I apologize for spreading misinformation.  

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • BMW Neue Klasse - a birth of a Sports Sedan

    BMW Neue Klasse - a birth of a Sports Sedan

    Unveiling of the Neue Klasse Unveiled in 1961, BMW 1500 sedan was a revolutionary concept at the outset of the '60s. No tail fins or chrome fountains. Instead, what you got was understated and elegant, in a modern sense, exciting to drive as nearly any sports car, and yet still comfortable for four.   The elegant little sedan was an instant sensation. In the 1500, BMW not only found the long-term solution to its dire business straits but, more importantly, created an entirely new
    History of the BMW 2002 and the 02 Series

    History of the BMW 2002 and the 02 Series

    In 1966, BMW was practically unknown in the US unless you were a touring motorcycle enthusiast or had seen an Isetta given away on a quiz show.  BMW’s sales in the US that year were just 1253 cars.  Then BMW 1600-2 came to America’s shores, tripling US sales to 4564 the following year, boosted by favorable articles in the Buff Books. Car and Driver called it “the best $2500 sedan anywhere.”  Road & Track’s road test was equally enthusiastic.  Then, BMW took a cue from American manufacturers,
    The BMW 2002 Production Run

    The BMW 2002 Production Run

    BMW 02 series are like the original Volkswagen Beetles in one way (besides both being German classic cars)—throughout their long production, they all essentially look alike—at least to the uninitiated:  small, boxy, rear-wheel drive, two-door sedan.  Aficionados know better.   Not only were there three other body styles—none, unfortunately, exported to the US—but there were some significant visual and mechanical changes over their eleven-year production run.   I’ve extracted t
  • Upcoming Events

  • Supporting Vendors

×
×
  • Create New...