• entries
    11
  • comments
    12
  • views
    1,433

Rear seat delete carpeting install

Sign in to follow this  
NYNick

261 views

I've gotten quite a few compliments, including esty herself, on my rear seat delete carpet installation. I basically followed her instructions on her website and the FAQ article by Mlittle, but I thought I'd document my experience here. It came out great.

 

First, I installed the carpet kit for the 'front' of the car. You've got to have the rear seat bottom upright done anyway to begin the rear seat area. Next, I lined the back part of the seat back with EZ Cool. While I was at it, I used a high speed recirculating saw to lop off those hooks that the rear seat back hangs onto. I also had run all the wires and installed the battery in the under portion of the back seat and used the seat belt bolt for my ground wire. Even ran the speaker wires so I wouldn't have to bother later. Might as well get all that stuff done beforehand.

 

My first move was to glue down the parcel shelf. This is a nice and level area and gives you a good reference line for the back carpet. I then used the carpet seat bottom piece and traced it onto a piece of luan plywood, about 1/8" thick. Cut this out with a jigsaw and test fitted in the car. Nice!

 

Basically, there's just a ton of test fitting throughout this whole job before gluing. The wheel humps took the longest because they're the first piece of the puzzle to glue. I'd put all the pieces in place, adjust, take them out, put them back, look, adjust etc. What I found was that the back carpet piece was too long and extended past the little protruding shelf that the bottom board is supported by. Because the wheel hump pieces also were too long, these pieces overlapped each other making a double layer of carpeting for the bottom board to push up against. This wouldn't do as it would leave too much of a gap in the back bottom.

 

Getting the wheel hump pieces just right took some trimming at the bottom. Too much and the bottom piece and board wouldn't cover the cut. Too little and it would create a double layer of carpeting. It was trial and error but once done I held them in place with some makeshift clamps and refit the whole thing one last time. Bingo! (BTW, I used a heat gun carefully on the back of the carpet to pre-fit/bend the wheel humps)

 

Holding the wheel hump pieces in place I outlined their position with magic marker so I knew where to spray the glue and where to put them back on. Finally I could get going on the rest of the pieces.

 

The rear piece has the parcel shelf as a reference as mentioned, but I also made sure the rear door cards were in place so that it got 'centered' as well. Once in place I bent the top portion down and sprayed, making sure it aligned well with the parcel shelf. Once stuck, I bent it up from the bottom and sprayed glue down there as well. Don't worry about the carpet being too long. Your bottom board is going to butt up against it and push it in.

 

Putting the board in place I pushed on it as hard as I could and drew pencil marks underneath where it overlapped the the rear seat upright. Since the upright is about 1" wide, I simply marked a line 1" further in and screwed 1x2's along that line. A test fit proved to take a hard push and a rubber mallet to get it in place, but it turned out fitting nice and snug.

 

esty gives you some excess vinyl for the front part of the board to trim it out. Some glue and some clothes pins and it was good to go!  I never even bothered gluing the bottom piece to the board. Why bother?

 

A minor detail was the curve where it meets the rear door cards. My carpet and board left a small opening where I could see down into the bottom of the seat area. With some spare Gobi tan vinyl I glued some onto the metal down there and voila! Blended right in.

 

All in all it took me about 5 hours. Sounds like a long time and it was, but the reward is well worth it!

 

Thanks to esty for a quality product!

20181230_142417.jpg

20181230_155137.jpg

20181230_155659.jpg

  • Like 1
Sign in to follow this  


5 Comments


Recommended Comments

27 minutes ago, mlytle said:

add this to the article on rear seat delete carpeting that already exists....

Thanks Marshall. Don't know how to do that though.

Share this comment


Link to comment

same way you post anywhere else on the site.  hit reply in the article and paste your info in.

 

 

 

Edited by mlytle

Share this comment


Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now