go to www.firstfives.org for all your e12 goodness. The problem with the fumes can be any number of vent or return fuel lines under the car. Also the seal for the sender or filler neck can be the prob ...
Dobbins brouthers here in NC does it but they are not always cheap. They do high quality work etc (LaValle's Import Restoration and Korman use them. shoot me an email rob.
you should get the one that weighs the least as that is rotational mass. even if your under weight right with those wheels that will allow you to ballance the car.
First off if one cylinder is bad replaceing it will blow out the other side very quickly. When one side is stronger then the other it will blow out the other side within a month or two. Save your self ...
the problem isnt so much the part number but knowing what size you need. There are at least 3 sizes if memory serves basicly you order them for a 318i 1984 and you will get the right ones.
Well to help when you remove the 02 sensor run the car on a nice drive for 15min to help it come off. Since the 02 sensor is moving take it to a muffler shop and have them put a new bung in. the 02 se ...
the question is which plate your talking about. There is a plate rivited on the inside of the Valve cover. LEAVE it there, that keeps as much oil from going though the system. If its a plate on the ou ...
Weight distrabution hitches are great, YES most surge brake systems can not run them. Drawtie makes a good one that I have used. Basicly it keeps your load stable between the two units. this is very i ...
Well I can add a few items of note from what we have seen at the shop. First off with any NLA item you still order it. you do this for two reasons. 1. they still have inventory even if the dealer cant ...
We have installed a few of the Dapbmw components and have been very happy with the quality. Here is the short rear bumper (early euro and turbo) on the supercharged car.
Do they have to be running? I have had lots of 02s that I have purchased that didnt run (and wont run again). Total number of 02s is around 20 total number of runners 3
the FAQ article is correct in its valve adjustmnet spec for all BMW cams (see blue binder). WHEN you set your valves too tight you wear out the cam. This also robs horsepower and fuel economy. the old ...
Get a new crush washer and set it good and tight. I am sure somwere there is a torque spec in inch lbsbut the usual good and tight is all thats required.
LT1BMW has nothing to do with the chev engine. Its the first 2 innitals of his real name the number 1 and BMW..... come on guys, O yeah he is part of the NC2002 MOB! Its funny how everyone is being ...
In the past year I have discovered 2 2002s a 73 and a 76 whos wiring harness did not match any of mine. Its well documented that a few of the production cars got leftovers or strange changes during pr ...
I would inspect both fenders carefully and replace the entire fender. I am not one who likes to deal with rust every year or so and fenders are cheap. Remember no matter what your going to be painting ...
BMW back in the day would change its harness designs due to supplier problems. The wiring diogram should always be checked and for the 76s they are actualy prety close in my experence. remember the bl ...
If we want to start banning people, remember this is how the FAQ got started is due to some geting banned, lets do it right. If you put a post on the wrong section your banned for a month... Mike Self ...
Well what caused the alternator to die, I just had one at the shop were the owner replaced the blown alternator. 2 months later we did the alternator and the voltage regulator. There is also a little ...
I would never use a toy dolly. Its hard on all the drive line including wheel bearings. If you dont care about the car then use a tow dolly and hope she doesnt break away and hit somthing.
Well first off shoot the person who did it. Then meda blast the rims (and the dead body). The meda blasting will strip away the chrome and other plateing materals used. This will usualy cost more but ...
Page 1 of 5
Goto page 1, 2, 3, 4, 5Next All times are GMT - 7 Hours
Topic: 
Forum Help
Forum Search
Register
Log in