Search found 55 matches

That one should work fine. Route it with a gentle radius to avoid binding. Tighten at the carb enough so it does not slip but avoid overtightening so as to not break the cable.

I checked again this weekend. Pulled the wheel after a drive and everything was hot , rotor, caliper, hub. I checked caliper and one piston did not seem to retract as smoothly as the others. The rotor ...

1981 - 17 years old -my first car a $300 1968 1600-2. Changed my life forever. Would I let my daughters drive one? Good question but I think it could be positive with the right person. Teach and stres ...

Rebuilt caliper and new rubber hoses all with 12,000 miles. How can I tell it's the brake binding? Car does not feel like it is pulling to left side but the hot wheel left me wondering about the brake ...

I drove home yesterday hearing a high pitched squeal coming from the left front wheel area. Mainly heard while driving straight above 20 mph and in left turns. Changes pitch in the turns and over bump ...

Thanks Max. I am confused with the picture though. Does that piece go below the air cleaner over the carb opening ( which is what i am looking for) or does it fit on the end of the air intake?

Looking for the oval rubber gasket / isolator that fits between the 2 bbl. carb. and air cleaner . I believe it is item 12 on this diagram.

Thanks

I had an oval shaped rubber gasket / isloator installed under a stock 2 bbl. air cleaner. It was about 1/2" tall. This piece sat on top of an aluminum adapter plate on top of a weber 2 bbl. DGV or 38 ...

Interesting as I have had a Behr, a Clardy, and a Frigiking and none of them looked like that. My clardy had only one row of vents. The frigiking was vertical on the sides ( did not flare out). The be ...

I have used graphite lube ( such as lock-eze) on plugs since my first 1600 in 1981. Threads are clean upon removal. Never a problem.

Any problem with resistor plugs WR8dc instead of W8dc? I use a Bosch red coil w/ pertronix and std. wires / connectors.

Thanks for any feedback!

I just had mine replaced this week. I bought the OEM seal in advance and my lockstrip was about 3 years old so i opted to re-use it. They quoted 300.00 installed. Of course there was some rust underne ...

Check steering box adjustment?

Mine did the same thing. If I recall I removed the seat and slightly bent the rail so that it ran flatter in the channel. This was on the left side only on my seat. I think if you remove the seat you ...

I used to run the taller one without any problems. I would check clearance with hood insulation, hood adjustment andmotor mounts to be sure.

I think C.D. is right as to what is salvagable; however A/C is very doable in an 02 if that's waht you want or need. I had a used Behr system installed 13 years ago and have enjoyed COLD air ever sinc ...

I am looking for a drivers side door handle in nice condition. e-mail @ landon@oddogws.com.

Thanks,

Delia, Where did you get the black faceplate that fits around the tuning buttons and dial?

Looking for the bottom piece that the shift boot attaches to. Excellent condition preferred.

Stunning! Beautiful car.

Stunning! Beautiful car.

I bought a kit recently and thought it to be pretty heavy duty and nice. My upholsterer pointed out that the pattern and seams were stamped. This would result in laying flat as opposed to the raised t ...

I had my flywheel lightened w/ an engine rebuild some years ago. I can't remember the weight but the machining was modest - nothing like a race car. The setup was for depndable street driving. It took ...

I am looking for the bottom shift surround piece from the Behr A/C. The part that the shifter boot attached to. Let me know if it's available and your price.

Thanks,

Landon

landon@oddogws.com

I am looking for the bottom shift surround piece from the Behr A/C. The part that the shifter boot attached to. Let me know if it's available and your price.

Thanks,

Landon

landon@oddogws.com

Had a local shop replace F & R stock springs and bilstein HD's. Car feels good at speed but there is a very pronouned popping sound heard when turning the wheels left or right at low speeds (< ...

How about the factory air cleaner?

Anyone know the difference between "standard" and "reinforced" springs as advertised by Wolleth & nesch? I currently run stock red dot springs with Bilstein HD's. I like the setup and would like to fr ...