Search found 700 matches

How about knowing how it is determined, then you never need to scratch for the answer!

It is the number of cable turns per mile. So take your driveshaf turns per mile and divide by the speedometer ...

Paper vs K&N. The stock paper filters better, K&N lets more dirt thru (proven face by an ISO filtration efficiency test). K&N per square inch if flow area has less restriction (less filtering) than p ...

.... THERE IS GAS SLOWLY DRIPPING OFF THE PASSENGER SIDE ROCKER PANEL AT THE FENDER-FRONT DOOR JUNCTION! I immediately siphon out a couple of gallons of gas and get the gas gauge back down to 3/4 and ...

Don't have your answer, but here is a way to determine if there are any differences. Go to Realoem and get the p/ns for both applications. If p/ns the same, you have one for sure.

Looks like my (up to now) reliable Delta Mk 10 capacitive discharge ignition system is dying, and I'm running out of replacements. Is there a contemporary CD system available? Or does anyone have a ...

Pistons are in the correct direction. Clean the raised portion off and you will find the arrow pointing forward.

PO probably got the cam/valve timing late because the dent is clean and valve has b ...

Just trying to lend a bit of intellegence to the topic.

Seems that not any more gap than .030" is necessary. The wider is better theory has no merit. Wider gaps induce spark jump to ground at the ...

Rather than just copy what the next guy does (with or without any real basis) go to EFI101 and search on John the J&S Electronic man (who produces a knock sensor system that adjusts spark advance on i ...

Rather than just copy what the next guy does (with or without any real basis) go to EFI101 and search on John the J&S Electronic man (who produces a knock sensor system that adjusts spark advance on i ...

After looking at the various write up on the chain tension adjuster, this is what I have assessed so far:

1) After installing the face plate with the tensioner lever in the "oil pool" area, coat th ...

Be sure you know that it is bad because a brake equipment part is a safety equipment part and the mfr will take it seriously. That's why all the inquiry.

4 full, 73 empty. Search is your friend, I gave it to the last guy.

i bought a tii booster a couple years ago and it is just now time to install it on the car but when you blow or suck on the vacuum port air comes through. so am i sol or can i rebuild it? if not does ...

Put your hose in the tank, use a rag to wrap around the hose and "seal" the opening, blow until you feel resistance, remove your mouth.

Fuel will usually begin to flow.

Engineers will say someth ...

There has been quite a bit of discussion about drive shaft alignment on the Vanagon Syncro Yahoo group. Syncro’s have a similar driveshaft in that they use the same guibo but don’t have a center supp ...

----The intake snorkle has a lever on the side of it. There are 2 outlets. One which I know goes to the carb filter, the other looks like it connects to the exhaust manifold. -----

More to the stor ...

I wouldn't get under the car with only a floorjack in the rear.....

... I had my dad spin the wheels really quickly while I watched the guage, and saw no deviation. Tried it at a couple location ...

I didn't figure the tip made much difference and not any more than what one in the 318 manifold extends. I used a 318 fuel rail with in and out moved to the ends.

I think the reason the 320 setup ...

It is special. It is a "tack" oil and is sticky so as to not drain off. Use some that from a motorcycle shop. Amsoil makes a spray on filter oil for their old filters of the same material. Use eit ...

The comparison and the injector install.

Yes it flows better, is better balanced (phyiscally) on the engine and for the 02 engine mounts. The throttle body bolt patter is different (3 studs vs 4 studs on the 318. Injectors can be hand fit, ...

Yes it flows better, is better balanced (phyiscally) on the engine and for the 02 engine mounts. The throttle body bolt patter is different (3 studs vs 4 studs on the 318. Injectors can be hand fit, ...

Don't know what it means either. You should have admitted ignorance and asked him what he was talking about. Some of these buzzwords baffle me.

From Sedalia, CO to Colo Springs and return by way of Deckers, CO.

Some photos at:

http://www.rmbmw2002.com/index.php?option=com_zoom&Itemid=27&catid=29

I have an early '02 ( VIN 1661387), and I am getting ready to have it painted. The previous owner had installed Vitaloni mirrors and drilled some extra holes in the drivers door. I would like to mak ...

The big one might be for the big plug in the front of the block. Another for the water outlet to the heater.
If you don't need to remove the joints where these might go, leave the joint alone or you ...

You are aware that one cap screw uses a gasketed washer, ok?

Mike posted here at times. His wife passed away suddenly to my suprise. Mike and Maria opened their home to the front range 02ers on a project work day on Mike's car. He has a young family. We alo ...

I have a driver's side block for you. Email me. There is a right and a left block.

I don't like a floor mess which is what a road tube will give you. I have no leaks on my garage floor.

I built an oil separator of same technology as on later cars like the S14 and return the oil ...