Search found 200 matches

74tii - My long ones(brake sylinder to rear tunnel and brake cylinder to passenger fender) also come in straight from Mobile Traditions.
As a side note, I needed the metal lines going from my calipe ...

As a side note, finally though with motor work and now on to body work on my 74tii which is Riveria Blue. Spoke with the guys at the paint store, if you go with a clear coat or chrom base, the Dupont ...

What would be the price for a newly re-built drivers side caliper?
Thanks

Looking for a good used drivers side (left)Tii caliper.
Have bought two new re-built ones from the local foreign parts guy and the outer bleeder has stripped on both. Now he says, a re-built one is ...

You don't by chance have a good used drivers side caliper for 74tii for sale do you?
Thanks
Ron

Thanks, will call this evening..

74tii- got over to the shop tonight to reset gap on the warm up regulator levered out instead of the cone all the down.
Got looking and found that the cone was already in the levered postion to wher ...

Thanks Justin,
Here's what I'm wondering now. Bought the KF pump because mine was bad. Since setting everything baseline according to the manual, found that the lever and stop was set at about 5 or ...

Unfortunately, I gapped it to the 2.6mm without levering. if there is good news it's that I no longer have to much fuel being pumped into the system which caused excessive smoke out the exhaust. Bad n ...

Caught some of the video, looks like all the retainer plate is doing is holding cone in a certain position. Can the cone get moved or something get out of place? I didn't hold anything in place when ...

74tii- after re-reading the manual, I now question myself on the gap setting between the lever and the stop.
I set the 2.6mm gap between lever and stop with engine cold and the rod all the way down ...

Thanks, the manual is what I'm going by to set everything, are you making it run richer by raising or lower the CO?

Even the though manual shows a 71-73 model tuna can , I have the little screw set ...

74tii - since I had the head had been re-built and have a different throttle body, KF pump, went back back through and set the baseline setup.
Was getting bas gas smoke, found the warm up regulator ...

74tii-Not looking to open a can of worms, but just put Royal Purple 75-90 in my tranny and diff. I've used RP in the past and it's always done good. I was like you and decided to call them due to th ...

cheez, that's a bit to far to drive. Would be perfect seats since I'm restoring with the Blue.
If you haven's sold them in a couple weeks, please do let me know and maybe we can work something out ...

Don't think it is the master cylinder due to the below and tried reading archives.
74Tii - part of a restore job. After getting her, replaced back brakes, front calipers and pads, brakes did good. Th ...

Where or what state are you located?
Thanks

74tii May sound goofy, but need quick confirmation. had the head re-built, got everything back together. Started her and was having a little idle surge problem that I didn't have before.
Read the a ...

For my own curosity, what problem/symptoms were you having that caused you to check it? Or was it just a FYI?

Thanks

thanks, I see now said the blind man..
Now it makes sense what they are saying in the manual.
ron

It'll be tomorrow night before getting to the shop to adjust the idle, but have my old housing here at the house.
Noticed after putting in my homemade 4mm piece in the hole of the housing that when b ...

simply enough.. thanks

74tii-
According to the tii fuel injection manual, to set the idle, put the hook into the frist lever slot, to set the idle the next step is to put a 4mm pin into the hole into the throttle housing(T ...

Thanks, I'm on vacation rest of the week, but will be going back at it next week. Had time to re-look at two of the linkages last night. both were a couple mm to long. Didn't get a chance to look ins ...

Bought the car not running, one of many things found that gas was not being sent to injectors. Bought another completer KF setup and replaced only the pump. The car started but was getting a lot of ga ...

74tii -That looks similar to the one I rented from AutoZone. If the pulley is made of hard plastic, good luck The center of mine is still on my old pump. Stipped the holes right out. it may work on t ...

Thanks Jerry,
I'll re-read, but i've downloaded, read and printed out the pages for adjusting, but it's still funny that they never discuss the third little rod or the length of it.
They discuss ...

The rod on my old setup was adjustable and the other KF system I had to buy also has an adjustable arm.

Reason for asking,
Had the head rebuilt and put on KF system (KF unit, injectors, tuna ca ...

74tii - Read the archives and the question has been asked, but not answered.
the pull rod should be 289mm (part A) and the linkage rod on the pump should be 85mm (part B).
The third little rod that ...

cool.. Thanks for the replies.
ron