Search found 205 matches

Did it work?

Oil Filter Adaptor Plate

This is a great product to make installing your Oil Pressure and Oil Temperature senders easy. This plate screws on under your oil filter and it has 4 1/8"N ...

Date: 6-13-06 12:50
From: Tiger75 in Shreveport, LA
Subject: steering Box Rebuild

Blunt,
I bought a spare to rebuild. It has taken a long time to get my parts together. Make sure th ...

The Haynes Automotive Repair Manual for 2002’s has a good section on steering box rebuilds, staring on page 182.

These are the parts that I replaced.

1) Upper (smaller) Shaft Seal 32111110269 ...

I have 4 i am not using.
Any body interested?

I use high temp brake grease. The kind you use on the back of brake pads. It doesn't melt cause it high temp and stays where you put it . but it is greasy and sticky. but works great

you told us too , Scott.
You said all the 02 people would be there!
Plus it's near Humberto's house!!!

Blunt, I have a copy if you need it.
Tim
Tiger75

I used a heat gun and every scraper tool that I had in the garage, first.
Then I used the orange citrus stuff. Helped a little .
Last I used acetone to get up the residual stuff but it is flamaable ...

yes

I got the following from Petronix yesterday

I have a 1974 BMW 2002 TII. I use the orginal distributor and two eariler
model Bosche Distributors. I want to convert each of my Dizzys to Pertr ...

I headed out Sunday AM
I hit the road at 6 am and headed South on the Pig Trail.
I only say two pick up trucks before 9 am and they were going the other way.
I had the road to myself for 3 hours an ...

I went to my local expert and have emailed Chris B who wrote the elec test quide on FAQ.

Problem is triodes - probably or one or more of the diodes in the rectifier.
I went to my local expert this ...

and i could see under there too good. Remember the Tii alt is mounted low.

The B+ voltage at idle was 13.56

The 14.03 volts was at the D+ terminal.
So my wire from alt to battaery is good.
I ...

I have an electrical question.

I was doing a test drive and getting my car in shape for a trip this weekend of about 800 to 900 miles to Mid America Fest in Arkansas. I am not really having any tr ...

You goin to Mid America in Eureka springs,Ark this weekend?
I will be there.
Tim

Is Bill Hiddle goin?
I only have an old eamil address and it comes back.

He is a Okie - Going Back to Tulsa one more time - I think.

Tim
Tiger75

I had the fuel and tempt guage bump and jump for a long time.
i ran a new ground wire from the battery to the instrument cluster and grounded ever where I could. I also cleaned all contact points to ...

I installed it on the oposite side of the car from the fuel pump. there was just more room there. be careful that fuel lines don't rub against the half shafts

I had to move mine caust i put a red t ...

I'll be at Skip's around noon.
Wanna go to lunch in Conway, somewhere?

We will be luckly to leave by 2.

If Daddy Danuel leads , it's about a 9 hour trip to Eureka, counting all the river fordin ...

I went on a factory tour in Munuch in the Summer of 1973.
I remember Germans in white coats with clipboards walking around watching the Italians on the line building 2002s.

See my write up on Tii Register

http://www.thetiiregister.com/phpmyfaq/index.php?action=artikel&cat=19&id=25&artlang=en

Knowledgebase » Upgrades
: M3 Starter Upgrade

I installed an M3 Star ...

I drove my Tii just over 100 miles with no alt and a fully charged battery.No radio, heater ac or lights were used. It was a long time ago- I did not even own the Tii yet. It was about a year later b ...

When an engine hunts at idle i.e. changes RPM over a narrow range,
Is this due to a fuel air ratio that is too lean?

Those that have contacted me via email recently already know this, but thought that I should let everyone know in case there are any lurkers out there.

Der Krewe of 02 is cancelled this year.
Ma ...

rat rod

I went to the Highland Parade (rolls Sunday afternoon) meeting last night since Troy could not go.
When I got to the meeting I found out that the forms and money were due last night, Jan 15th.

I ...