Search found 280 matches

have you checked the fuel pump?
When my fuel pump went out it, it the output of the pump decreased significantly but the pump continued to run. The car would run fine for a while, then it would bog ...

Clogged pickup screen inside the tank?
or the tiny mesh filter just before the pump?
or the fuel filter on radiator support?
or the mesh filter at the K-F pump inlet?

Try all basics before you s ...

Great pictures Steve, love the blue and black plates, looks like some long time owners (or those "re-using" old plates).

when i intalled [url=https://http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,296517/highlight,/]my headers i came up from the bottom and didn't need to unbolt the engin ...

I know the feeling, I'll be working on 32 years this December.

congrats Mike!!

Don't give up!! Keep up the faith!!

Pour some oil down the pressure sender to prime it.

reply to c.kikawa at comcastdotnet.

I embarked on similar quest a few years back. The question is a good one and hasn't really had a definitive answer, because there isn't one. There are too many variables to deal with and one person' ...

My wife describes it as "having sex with my car." Nuff said.

My girlfriend calls Phoenix my "Mistress" since I spend all my weekends wrenching.

I'm in the same boat as you guys. The weekends are ...

Pictures please!!

the 292. A wide-band 02 sensor and gauge could answer that. ....
Moving a tii off of dead stock is tricky and provides little power to dollars spent, Yes, I can say that.

However, you just need ...

before you go the KF rebuild route, did you:
-drain the gas tank and refill with fresh gas?
-check and clean the in-tank screen?
-check and clean the two screens in the fuel lines (one before the ...

What a beaut Steve!!

Looks Fantastic Bill!
Just read the P2 Project Blog.
Well done and looks great. Keep up the beautiful work

Bill,
It looks like you bypassed the expansion cylinder.
Any issues with that???

Just to be clear, if the leak was coolant/water, replacing the o-rings would not have any impact - it will fix a fuel leak.

The only place where coolant comes into the KF unit is via the warm up s ...

74tii
Can this piece be purchased or replaced? Ron
For ignition timing on a tii, use the ball in the tranny housing method - just like all '02s (or use your ear).
For a tii, there is a notch in th ...

the aux linkage is designed to compensate for using a different cam. Adjustng the verbotten screw richens the mix across the board.

Short of going with a full KF reuild to match a different cam, t ...

I would love the PDF

also available from the [url=http://www.thetiiregister.com/phpmyfaq/index.php?sid=200098&lang=en&action=artikel&cat=220444&id=14&artlang=en]tii Register

Great write up on the door actuators Harrison!!
I'll have to add this to the project list for this year.
Keep up the excellent work!!

the M3/S14 oil filter head is the way to go.
it includes a thermotat and temp (?) and pressure senders.

register and post on s14.net in the parts section for an oil filter head.
i got mine for ~ ...

So sorry to hear about Mae but glad to hear you're okay.
Don't be surprised if you're sore over the next couple of days.

Another source is Rob over at 2002haus.
No affliation and he's a FAQ supporter.

For WA, it is a one time fee, i paid $50 for a Collector plate fee and don't need a front plate. No renewal fee and no emissions testing.

Here's the particulars:
Collector vehicles must be:
-at ...

Bill
The hairpin cllip is shown from this picture. This setup looks exactly like mine, down to the three different holes on the warm-up regulator, the extra washers stacked on the linakge to adjust t ...

i'll try to get some more posted this w/e - gotta find the camera first....

The wire (linkage) does not go though the bolt in the middle.

I'm not an expert on cams nor engine re-building and what I know is from what I've been told by various mechanics and is consistent with others on the board.
A 292 cam will breath more, especially a ...

One off my pumps has that same wire but I am not sure what it is for or how to hook it up.
My suspicion is that it is a way to provide more fuel to bigger motors.
The wire on my KF is used as an a ...

Bummer that the original style caps are NLA.

Blunt, i'll email you separately
thanks

Blunt,
can you also get the correct "mushroom" dust caps?

let me know, thanks