Search found 113 matches

So I've been driving the car around a little bit lately and I have been hearing a little bit of rubbing coming from the rear end on even the slightest of bumps. My car has always looked really low in ...

Frank,

I just have a temporary piece for now. It is 1/4" luaun board with carpet on top. I will eventually wrap something different in vinyl that will fit the form of the seats better.

http:// ...

I installed the seatbelts and have finally been driving the car around a little. I got seatbelts for a E-28. Not a direct bolt in, but happened to fit very nicely with the M seats. Hopefully will f ...

Been a while since my last update and I have done alot since then too. I finished building and installing the rear strut bar and have finished the carpet. I am so close to driving the car now, I rea ...

Plum Island - Nelson Demille

Tyrel

Also, do I still have to have a ground from the motor?

Tyrel

The paint is gone behind that large washer, the strut bar is bare there, and I cleaned off the paint from the strut tower itself.

Thanks,

Tyrel

I just finished moving the battery to the trunk and putting in my rear strut bar. When I got it all hooked up I tried starting the car. The starter just clicks repeatedly. It is probably something ...

Started building the rear strut bar today. I got the tray that the battery will sit in and the bar across the two towers built. Unfortunately I ran out of welding gas today, so I couldn't finish it ...

Sorry to hear about your 2002, but glad to hear that you are alright!

Tyrel

So I went on a rampage of putting the car back together this morning. I got the driver's side essentially finished up. Turned out even better than I had imagined. Now I just have to get my audio gu ...

I just kept the stock 2002 belts.

Tyrel

Thanks! I got my carpet from Chris Willet at Only02.com

Tyrel

looks great so far, i can only hope my carpet looks as nice as yours once its in.

one suggestion: duct tape will release after it gets wet a few times, and it tends to melt in heat. I'd go over you ...

Got alot done yesterday. I got the dash in, and all of the wiring for the front seats. I also got the two quarterlight windows and their seals in. The carpet even started getting glued down last ni ...

Headliner is finished. It turned out better than expected. Now I am on the home stretch of putting the car back together.

http://i41.photobucket.com/albums/e299/742002/FullHeadlinerrear.jpg

Ty ...

Here is the FatMat installed.

http://i41.photobucket.com/albums/e299/742002/FatMatFinished2.jpg

Tyrel

Got the headliner hung and glued today. It really wasn't nearly as bad as I thought that it was going to be. It only has one small wrinkle in it, and its in a place that I will never see it. I also ...

Got the map light wiring in and the lights working last night. I also got the dome light put into the roof.

http://i41.photobucket.com/albums/e299/742002/DomeLightin.jpg

Tyrel

What type/brand of rims is that? Good luck with that project.

Those are the 15 x 7's from Ireland Engineering.

Tyrel

I finished painting the underside of the roof and just have to finish wiring in the map lights for the rear view mirror. After that I can truly start putting the headliner in!

Tyrel

Yes! Finally done with the floors. I thought it was just the passenger side front that was rotten. Silly me. I ended up replacing spots in the front and rear driver's side and the rear passenger s ...

Looks really great! Nothing like new paint to get enthusiastic about putting a car back together!

Tyrel

Now in the past hour or two I have been putting the new floor in. The difference is amazing after looking at the before and after of the floor.

Before:

http://i41.photobucket.com/albums/e299/74 ...

It felt so great to get the seat mounts figured out. Now it was time to deal with the rusty passenger floor. I tore the old one out and was very happy to find that my frame rail still looked great u ...

So, after all of the excitement of V@V I got home a started trying to mount my Z3 M Coupe seats. I figured out the wiring and then designed and built the mounts. The seats sit at just about the sam ...

The trip to V@V was tons of fun and it gave me some more motivation to get going on my project. My father and I drove down to North Carolina and had a really great time at the show. I ended up buyin ...

Put it in a vise and hit it with a hammer.

Tyrel

The mirror is very simple...it goes in the exact same way as the original.

Tyrel

So I ordered a new front floor and am now waiting on that to come in. In the mean time I have another goodie to install. I want to thank Keith from www.my2002tii.com for the idea on this one. It i ...