Search found 73 matches

Thought this might be of interest to some:

http://l.yimg.com/us.yimg.com/feeds/us/grn/Green_EcoGeek/fakeisetta.jpg

http://green.yahoo.com/blog/ecogeek/488/rumors-fly-around-an-all-electric-bmw.h ...

Sorry to hear it, I went to his site more than several times to read up on some vintage bikes and components. One of the few fairly comprehensive sites on such things.

If it runs, (and runs good) I'd consider it. Also, have you done many transmission replacements? You'll spend quite a bit for a transmission, but I'd consider converting to a manual and run it for a ...

Is the stepside yours, too? And the short fleet bed?

Cool, a bicentennial plate - I haven't seen one of those in a while. Is the plate original to you car? Is that considered a historical plate?

I'd pay a reputable dealer for one. Mine was about $350 with shipping. You can find bargains, but until you bolt it in, you don't know if the limit slip is worn out. The only way to get a good deal ...

Are you wanting to buy or sell?

Just a thought, I'd look at the nut on top of the strut first, being that was the last repair made. Make sure it's tight and doesn't turn the shaft of the strut insert when trying.

The top bearing ...

I put 195/50/15 Falken's on mine and had rubbing issues in the passenger side rear. Took a die grinder with a cut off wheel and trimmed an eighth of an inch at a time, with test drives in between. O ...

Just trying to give you some ideas, I haven't ever removed the ignition cylinder that I can recall. I think you have to put the key in to remove it??? Have you removed the ignition switch from the b ...

Does the engine have a good ground? When you test the plug, earth it to the body and the engine and see if either work?

is the tranny from the 318i the same as an 02 but without the mech speedo?

yes - '84 & '85 only - mounted to the m10 block - as noted there's no place for a mechanical speedo cable. Not 100% on th ...

Here's a couple from my lens. Just loved the drive, there aren't too many roads in Oklahoma like that. Thanks again Bo & Barb and Co. for all your hard work.

You could probably afford Rota's ( or close to it) if you really want to give up the Mahle's

http://cgi.ebay.com/ebaymotors/BMW-2002-Tii-13-x-5-wheels-SET-OF-FIVE-Mahle-74-75-76_W0QQcmdZViewItemQQc ...

the PM doesn't work

Feel free to PM me if anyone decides on leaving Saturday morning. I'm looking at leaving Tulsa at 5am Saturday morning to make the Eureka Inn Best Western at 8:30. (101 E. Van Buren). Should be ple ...

That'd be at least 7 '02s then, if my work schedule doesn't change. I'll call Bo if I don't get a response to the email. Just didn't want to interupt his Sunday...

Anyone going from the board? Haven't seen too many posts about it yet.

I'm planning on leaving Tulsa early Saturday if anyone wants to meet up. Still trying to find what time I'd have to meet up ...

When you do have some spare time, and absolutely nothing better to do, a wire wheel on a die grinder and some POR-15 would do wonders for those trailing arms and half shafts. Of course, you'll have t ...

I agree with Jack - I'd remove the locking assembly from the door and degrease and clean it before applying more grease. The old grease builds up on there and make it hard to operate.

I got a couple of spacers from Dave - they were 2 or 3 mm thick. He's got different sizes in aluminum. Don't know about hub-centric. You'll have to determine your stud length with the spacer you ch ...

The VIN is punched in the cowl area on US spec cars along with having a separate aluminum VIN tag in the engine compartment.

There's a number of differences in sheet metal that complicate changing ...

Just my opinion, but anything that is not 2002 specific, is not a frequently asked question about '02s and would belong on the off topic board. Not trying to chase anyone away, but a multitude of pos ...

Please use the off-topic forum...

Cool, thanks. Just thought of one other thing - I've got vented front rotors on tii struts - I wonder if that would put the wheels out any farther that stock rotors?

I noticed the group buy awhile back, after it had been sold out. Don't get on the board too much these days. Found some 25mm offset RB's on eBay for a reasonable amount and buyed 'em now. Hub centr ...

Anyone know the standard length for front wheel studs on the 2002/tii? I've got some one the front that are too short that I'd like to replace with the correct length before we get into the driving s ...

My work schedule has changed last I heard. I may be able to make this one after all! I've put it on the calendar, so, if overtime doesn't interfere...

Anyone have a TV tuner card in their computer? My 2nd cheap DVD player died last night. Thinking I need to get away from cheap entertainment system components and use the DVD in my PC.

Looking to ...